Liftmaster 888LM MyQ Control Panel Bedienungsanleitung PDF herunterladen (Seite 3)

PUSH BAR

Press the push bar to open/close the door.

LIGHTS

Press the LIGHT button to turn the garage door opener lights on or off.

When the lights are turned on they will stay on until the LIGHT button is

pressed again, or until the garage door opener is activated. Once the

garage door opener is activated the lights will turn off after the specified

period of time (the factory setting is 4-1/2 minutes). The LIGHT button

will not control the lights when the door is in motion.

To change the amount of time the garage door opener lights will stay on:

Press and hold the LOCK button until the garage door opener lights flash.

The time interval is indicated by the number of flashes.

Light Feature

The lights will turn on when someone enters through the open garage

door and the safety reversing sensor infrared beam is broken.

Activate:

Start with the garage door opener lights on. Press and hold the LIGHT

button until the garage door opener lights turn off, then on again.*

Deactivate:

Press and hold the LIGHT button until the garage door opener lights

turn on, then off again.*

* Approximately 10 seconds

FUNCTIONS

NUMBER OF TIMES GARAGE

DOOR OPENER LIGHTS FLASH

1234

TIME THE GARAGE DOOR

OPENER LIGHT STAYS ON

1 ½

Minutes

2 ½

Minutes

3 ½

Minutes

4 ½

Minutes

MOTION SENSOR

This feature will automatically turn on the garage door opener lights when

motion is sensed. The lights will come on for the set period of time, then

shut off.

Activate/Deactivate:

Slide the motion sensor switch ON or OFF.

TIMER-TO-CLOSE (TTC)

NOTE: DO NOT install this door control on garage door opener systems

controlling one-piece or swing doors.

The TTC feature automatically closes the door after a specified time

period (1, 5, or 10 minutes). Once the TTC has been set and the door is

open, the LED for the selected close interval will blink and begin to count

down to close the door. The control panel will beep and the garage door

opener lights will flash before closing the door.

The TTC feature will deactivate if the garage door encounters an

obstruction twice; or the safety reversing sensors are incorrectly installed.

The garage door will reverse open and WILL NOT close until the

obstructions are clear or the safety reversing sensors are correctly

installed. When the obstruction has been cleared or the safety reversing

sensors have been aligned, the door will close when the garage door

opener is activated.

Activate:

Press and hold the ON button until one of the TTC LEDs light up. Then

press the ON button again to cycle through the time interval options

(the corresponding TTC LED will light for each time interval). The

garage door opener light bulbs will blink as confirmation.

Deactivate:

Press and hold the OFF button until all TTC LEDs turn off and a beep is

heard from the control panel.

Temporarily hold door open (suspend TTC):

Press and release the HOLD OPEN button. The HOLD OPEN button will

begin to flash. Press the HOLD OPEN button again to resume normal

TTC operation.

LOCK

Activate*:

Press and hold the LOCK button for 2 seconds. The command LED will

flash as long as the lock feature is activated and your handheld remote

control will not operate your door at this time.

Deactivate:

Press and hold the LOCK button again for 2 seconds. The command

LED will stop flashing and normal operation will resume.

* Your LiftMaster

keypad will continue to work when the LOCK has been

activated.

LIGHT

Button

1 Minute

TTC LED

5 Minute

TTC LED

10 Minute

TTC LED

ON Button

Command

LED (yellow)

OFF Button

HOLD OPEN

Button

Motion

Sensor

LEARN

button

Learn LED

(Red)

LOCK

button

Push Bar

1 2 3 4 5 6 7 8 ... 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Liftmaster 888LM MyQ Control Panel Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheit Liftmaster 888LM MyQ Control Panel